The pitzDaily case uses a lot of mesh grading close to walls and the shear layer.
Prior to v2.4, blockMesh only permitted grading in one direction within a single block,
so the pitzDaily mesh comprised of 13 blocks to accommodate the complex grading pattern.
blockMesh has multi-grading that allows users to divide a block in a given direction and
apply different grading within each division. The mesh generated with blockMesh using
13 blocks has been replaced with a mesh of 5 blocks that use multi-grading. The new
blockMeshDict configuration produces a mesh very similar to the original 13-block mesh.
- this makes it possible to perform additional operations
on surface values that have been previously sampled.
- support vectorField for weighting operations.
- reduce overhead by avoiding creation of weight fields, Sf fields
and combined surface geometries unless they are actually required.
- extend some similar concepts and operations to volFieldValue
Both stardard SIMPLE and the SIMPLEC (using the 'consistent' option in
fvSolution) are now supported for both subsonic and transonic flow of all
fluid types.
rhoPimpleFoam now instantiates the lower-level fluidThermo which instantiates
either a psiThermo or rhoThermo according to the 'type' specification in
thermophysicalProperties, see also commit a1c8cde310
Both stardard SIMPLE and the SIMPLEC (using the 'consistent' option in
fvSolution) are now supported for both subsonic and transonic flow of all
fluid types.
rhoSimpleFoam now instantiates the lower-level fluidThermo which instantiates
either a psiThermo or rhoThermo according to the 'type' specification in
thermophysicalProperties, e.g.
thermoType
{
type hePsiThermo;
mixture pureMixture;
transport sutherland;
thermo janaf;
equationOfState perfectGas;
specie specie;
energy sensibleInternalEnergy;
}
instantiates a psiThermo for a perfect gas with JANAF thermodynamics, whereas
thermoType
{
type heRhoThermo;
mixture pureMixture;
properties liquid;
energy sensibleInternalEnergy;
}
mixture
{
H2O;
}
instantiates a rhoThermo for water, see new tutorial
compressible/rhoSimpleFoam/squareBendLiq.
In order to support complex equations of state the pressure can no longer be
unlimited and rhoSimpleFoam now limits the pressure rather than the density to
handle start-up more robustly.
For backward compatibility 'rhoMin' and 'rhoMax' can still be used in the SIMPLE
sub-dictionary of fvSolution which are converted into 'pMax' and 'pMin' but it
is better to set either 'pMax' and 'pMin' directly or use the more convenient
'pMinFactor' and 'pMinFactor' from which 'pMax' and 'pMin' are calculated using
the fixed boundary pressure or reference pressure e.g.
SIMPLE
{
nNonOrthogonalCorrectors 0;
pMinFactor 0.1;
pMaxFactor 1.5;
transonic yes;
consistent yes;
residualControl
{
p 1e-3;
U 1e-4;
e 1e-3;
"(k|epsilon|omega)" 1e-3;
}
}
The fundamental properties provided by the specie class hierarchy were
mole-based, i.e. provide the properties per mole whereas the fundamental
properties provided by the liquidProperties and solidProperties classes are
mass-based, i.e. per unit mass. This inconsistency made it impossible to
instantiate the thermodynamics packages (rhoThermo, psiThermo) used by the FV
transport solvers on liquidProperties. In order to combine VoF with film and/or
Lagrangian models it is essential that the physical propertied of the three
representations of the liquid are consistent which means that it is necessary to
instantiate the thermodynamics packages on liquidProperties. This requires
either liquidProperties to be rewritten mole-based or the specie classes to be
rewritten mass-based. Given that most of OpenFOAM solvers operate
mass-based (solve for mass-fractions and provide mass-fractions to sub-models it
is more consistent and efficient if the low-level thermodynamics is also
mass-based.
This commit includes all of the changes necessary for all of the thermodynamics
in OpenFOAM to operate mass-based and supports the instantiation of
thermodynamics packages on liquidProperties.
Note that most users, developers and contributors to OpenFOAM will not notice
any difference in the operation of the code except that the confusing
nMoles 1;
entries in the thermophysicalProperties files are no longer needed or used and
have been removed in this commet. The only substantial change to the internals
is that species thermodynamics are now "mixed" with mass rather than mole
fractions. This is more convenient except for defining reaction equilibrium
thermodynamics for which the molar rather than mass composition is usually know.
The consequence of this can be seen in the adiabaticFlameT, equilibriumCO and
equilibriumFlameT utilities in which the species thermodynamics are
pre-multiplied by their molecular mass to effectively convert them to mole-basis
to simplify the definition of the reaction equilibrium thermodynamics, e.g. in
equilibriumCO
// Reactants (mole-based)
thermo FUEL(thermoData.subDict(fuelName)); FUEL *= FUEL.W();
// Oxidant (mole-based)
thermo O2(thermoData.subDict("O2")); O2 *= O2.W();
thermo N2(thermoData.subDict("N2")); N2 *= N2.W();
// Intermediates (mole-based)
thermo H2(thermoData.subDict("H2")); H2 *= H2.W();
// Products (mole-based)
thermo CO2(thermoData.subDict("CO2")); CO2 *= CO2.W();
thermo H2O(thermoData.subDict("H2O")); H2O *= H2O.W();
thermo CO(thermoData.subDict("CO")); CO *= CO.W();
// Product dissociation reactions
thermo CO2BreakUp
(
CO2 == CO + 0.5*O2
);
thermo H2OBreakUp
(
H2O == H2 + 0.5*O2
);
Please report any problems with this substantial but necessary rewrite of the
thermodynamic at https://bugs.openfoam.org
Henry G. Weller
CFD Direct Ltd.
e.g. the motion of two counter-rotating AMI regions could be defined:
dynamicFvMesh dynamicMotionSolverListFvMesh;
solvers
(
rotor1
{
solver solidBody;
cellZone rotor1;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega 6.2832; // rad/s
}
}
rotor2
{
solver solidBody;
cellZone rotor2;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega -6.2832; // rad/s
}
}
);
Any combination of motion solvers may be selected but there is no special
handling of motion interaction; the motions are applied sequentially and
potentially cumulatively.
To support this new general framework the solidBodyMotionFvMesh and
multiSolidBodyMotionFvMesh dynamicFvMeshes have been converted into the
corresponding motionSolvers solidBody and multiSolidBody and the tutorials
updated to reflect this change e.g. the motion in the mixerVesselAMI2D tutorial
is now defined thus:
dynamicFvMesh dynamicMotionSolverFvMesh;
solver solidBody;
solidBodyCoeffs
{
cellZone rotor;
solidBodyMotionFunction rotatingMotion;
rotatingMotionCoeffs
{
origin (0 0 0);
axis (0 0 1);
omega 6.2832; // rad/s
}
}
using a run-time selectable preconditioner
References:
Van der Vorst, H. A. (1992).
Bi-CGSTAB: A fast and smoothly converging variant of Bi-CG
for the solution of nonsymmetric linear systems.
SIAM Journal on scientific and Statistical Computing, 13(2), 631-644.
Barrett, R., Berry, M. W., Chan, T. F., Demmel, J., Donato, J.,
Dongarra, J., Eijkhout, V., Pozo, R., Romine, C. & Van der Vorst, H.
(1994).
Templates for the solution of linear systems:
building blocks for iterative methods
(Vol. 43). Siam.
See also: https://en.wikipedia.org/wiki/Biconjugate_gradient_stabilized_method
Tests have shown that PBiCGStab with the DILU preconditioner is more
robust, reliable and shows faster convergence (~2x) than PBiCG with
DILU, in particular in parallel where PBiCG occasionally diverges.
This remarkable improvement over PBiCG prompted the update of all
tutorial cases currently using PBiCG to use PBiCGStab instead. If any
issues arise with this update please report on Mantis: http://bugs.openfoam.org
Description
Constrain the field values within a specified region.
For example to set the turbulence properties within a porous region:
\verbatim
porosityTurbulence
{
type scalarFixedValueConstraint;
active yes;
scalarFixedValueConstraintCoeffs
{
selectionMode cellZone;
cellZone porosity;
fieldValues
{
k 30.7;
epsilon 1.5;
}
}
}
\endverbatim
See tutorials/compressible/rhoSimpleFoam/angledDuctExplicitFixedCoeff
constant/fvOptions for an example of this fvOption in action.
The modes of operation are set by the dimensions of the pressure field
to which this boundary condition is applied, the \c psi entry and the value
of \c gamma:
\table
Mode | dimensions | psi | gamma
incompressible subsonic | p/rho | |
compressible subsonic | p | none |
compressible transonic | p | psi | 1
compressible supersonic | p | psi | > 1
\endtable
For most applications the totalPressure boundary condition now only
requires p0 to be specified e.g.
outlet
{
type totalPressure;
p0 uniform 1e5;
}
To re-use existing 'sampleDict' files simply add the following entries:
type sets;
libs ("libsampling.so");
and run
postProcess -func sampleDict
It is probably better to also rename 'sampleDict' -> 'sample' and then run
postProcess -func sampleDict
