- input: added support (similar to DynamicList)
- output: redirect through UList output, which enables binary etc
- these changes enable support for broadcast and other parallel IO
for std::vector
ENH: support SubList of std::vector (entire length)
- allows a 'glue' layer for re-casting std::vector to UList etc
- when running with "errors warn;" it will reset the warnings counter
(if any) when it returns to a good state.
This re-enables un-suppressed warnings for the next cycle.
Also reset the warnings counter on end().
ENH: add short-circuit in HashTable::erase(key)
- skip and return false if the table is empty or the key is not found.
This makes for faster no-op behaviour.
- for workflows with appearing/disappearing patches (for example)
can specify that empty surfaces should be ignored or warned about
instead of raising a FatalError.
Note that this handling is additional to the regular top-level
"errors" specification. So specifying 'strict' will only actually
result in a FatalError if the "errors" does not trap errors.
- "ignore" : any empty surfaces are simply ignored and no
file output (besides the header).
- "warn" : empty surfaces are warned about a few times (10)
and the file output contains a NaN entry
- "strict" : corresponds to the default behaviour.
Throws a FatalError if the surface is empty.
This error may still be caught by the top-level "errors" handling.
- support UList shallowCopy with pointer/size
(eg, for slicing into or from span)
ENH: add SubList::reset() functionality
- allows modification of a SubList after construction.
Previously a SubList had an immutable location after construction
and there was no way to shift or change its location.
BUG: missed special handling for DynamicList<char>::readList (fixes#2974)
- equivalent to List<char>::readList, in which the stream is
temporarily toggled from ASCII to BINARY when reading in a List of
char data.
This specialization was missed when DynamicList<T>::readList() was
fully implemented.
- defines values for EMPTY, UNIFORM, NONUNIFORM and MIXED
that allow bitwise OR reduction and provide an algorithm
for calculating uniformity
ENH: consolidate more efficient uniformity checks in PackedList
ENH: improve linebreak handling when outputting small matrices
- use ignore instead of seekg/tellg to swallow input (robuster)
- check for bad gcount() values
- wrap Foam::fileSize() compressed/uncompressed handling into IFstream.
- improve handling of compressed files in masterUncollatedFileOperation.
Previously read into a string via stream iterators.
Now read chunk-wise into a List of char for fewer reallocations.
- soft renames (ie, old names still available via typedefs) for more
reasonable names and more coverage with std stream variants.
The old names could be a bit cryptic.
For example, uiliststream (== an unallocated/external list storage),
which is written as std::ispanstream for C++23.
Could similarly argue that IListStream is better named as
ICharStream, since it is an input stream of characters and the
internal storage mechanism (List or something else) is mostly
irrelevant.
Extending the coverage to include all std stream variants, and
simply rewrap them for OpenFOAM IOstream types. This simplifies the
inheritance patterns and allows reuse of icharstream/ocharstream as
a drop-in replace for istringstream/ostringstream in other wrappers.
Classes:
* icharstream / ICharStream [old: none / IListStream]
* ocharstream / OCharStream [old: none / OListStream]
* ispanstream / ISpanStream [old: uiliststream / UIListStream]
* ospanstream / OSpanStream [old: none / UOListStream]
Possible new uses : read file contents into a buffer, broadcast
buffer contents to other ranks and then transfer into an icharstream
to be read from. This avoid the multiple intermediate copies that
would be associated when using an istringstream.
- Use size doubling instead of block-wise incremental for ocharstream
(OCharStream). This corresponds to the sizing behaviour as per
std::stringstream (according to gcc-11 includes)
STYLE: drop Foam_IOstream_extras constructors for memory streams
- transitional/legacy constructors but not used in any code
- nonBlocking: receive before send
- nonBlocking: wait for receive requests, process and then wait for
other requests. Can be extended to use polling...
- the 'fake' send (to self) now send copies into recv buffers instead
of send buffers.
This provides a clear separation of send and receive fields
- avoid unnecessary reallocations with PtrList of send/recv buffers
- remove outer looping for accessAndFlip and pass target field
as parameter for inner looping instead
ENH: refine mapDistribute send/recv requests handling
- separate send/recv requests for finer control
- receive does not need access to PtrList of sendBuffers, since the
send-to-self now uses the recvBuffers
- totalSize() returns retrieve the linear (total) size
(naming as per globalIndex)
- operator[] retrieves the referenced value (linear indexing)
- labels() returns a flattened labelList (as per labelRange itself)
- broadcasts list contiguous content as a two-step process:
1. broadcast the size, and resize for receiver list
2. broadcast contiguous contents (if non-empty)
This avoids serialization/de-serialization memory overhead but at
the expense of an additional broadcast call.
The trade-off of the extra broadcast of the size will be less
important than avoiding a memory peak for large contiguous mesh data.
REVERT: unstable MPI_Mprobe/MPI_Mrecv on intelmpi + PMI-2 (#2796)
- partial revert of commit c6f528588b, for NBX implementation.
Not yet flagged as causing errors here, but eliminated for
consistency.
- simplifies use with other allocators (eg, memory pools).
Can also be used with other containers.
vectorField fld = ...;
sigFpe::fillNan(fld.data_bytes(), fld.size_bytes());
COMP: inline sigFpe::ignore helper class
- now unused (may be removed in the future), but can avoid compiling
code for it
COMP: missing sigStopAtWriteNow() definition for MSwindows
- simplifies internal handling (like a fileName) and allows the
dictionary name to be used with unambiguous addressing.
The previous dot (.) separator is ambiguous (ie, as dictionary
separator or as part of a keyword).
ENH: foamDictionary report -add/-set to stderr
- selected with '+strict' in WM_COMPILE_CONTROL or 'wmake -strict', it
enables the FOAM_DEPRECATED_STRICT() macro, which can be used to
mark methods that are implicitly deprecated, but are not yet marked
as full deprecated (eg, API modification is too recent, generates
too many warnings). Can be considered a developer option.
- since the Apple SIP (System Integrity Protection) clears environment
variables such as DYLD_LIBRARY_PATH, a number of workarounds have
been used to provide shadow values. However, for a more robust
installation using -rpath at compilation time appears to be the
better solution.
In addition to the usual -rpath specification with absolute file
paths, MacOS supports (@loader_path, @executable_path) as well.
Now default to link with rpath information for MacOS, which can be
disabled by adding `~rpath` in WM_COMPILE_CONTROL
Explicit library paths handled:
- FOAM_FOAM_EXT_LIBBIN, FOAM_EXT_LIBBIN/FOAM_MPI
The executable rpaths are handled assuming a structure of
install-path/bin
install-path/lib/$(FOAM_MPI)
install-path/lib
Absolute compile-time paths for FOAM_USER_LIBBIN, FOAM_SITE_LIBBIN
and FOAM_LIBBIN are not handled since these are either too fragile
(FOAM_USER_LIBBIN and FOAM_SITE_LIBBIN values) or covered via
@loader_path anyhow (FOAM_LIBBIN).
Since the value of FOAM_MPI is a compile-time value, this rpath
treatment makes the installation less suitable for runtime changes
to the MPI vendor/version.
Note: no rpath added for c-only compilations since there are
currently no c-only libraries or executables with dynamic loading
- eliminate ClassName in favour of simple debug
- include Apple-specific FPE handling after local definition
to allow for more redefinitions
COMP: remove stray <csignal> includes
- naming like std::map::try_emplace(), it behaves like emplace_set()
if there is no element at the given location otherwise a no-op
ENH: reuse existing HashPtrTable 'slot' when setting pointers
- avoids extra HashTable operations
- the construction of compound tokens is now split into two stages:
- default construct
- read contents
This permits a larger variety of handling.
- the new token::readCompoundToken(..) method allows for simpler
more failsafe invocations.
- forward resize(), read() methods for compound tokens to support
separate read and population.
Top-level refCompoundToken() method for modify access.
ENH: split off a private readCompoundToken() method within ISstream
- this allows overloading and alternative tokenisation handling for
derived classes
- simplifies iteration of ITstream using nRemainingTokens() and skip()
methods or directly as a list of tokens.
The currentToken() method returns const or non-const access to
the token at the current tokenIndex.
The peekToken(label) method provides failsafe read access to tokens
at given locations.
ENH: add primitiveEntry construct with moving a single token
Increase usage of std algoritms within the OpenFOAM List classes. Remove reliance on linked-list during reading
See merge request Development/openfoam!620
